全国服务热线:

021-51698378

进口井用潜水泵

名称
进口井用潜水泵
压力
1.6MPa
型号
GR
口径
DN40-DN200
材质
铸铁、不锈钢
进口井用潜水泵
  • 质量:从铸件到产品,实行全过程质量监控,全方位检测,责任到人!
  • 价格:高效成本控制,自产自销,减少中间环节,让利于客户!
  • 交货:充足的库存,上海便捷物流,缩短交货期,严格按照合同期交货!
销售热线:021-51698378
图文传真:021-69519069
服务电话:13524269805

英国GRIMM格林进口井用潜水泵 UK GRIMM Submersible pumps for imported wells

进口井用潜水泵.jpg

英国GRIMM格林进口井用潜水泵概述:

          进口井用潜水泵是根据国际标准设计的节能产品,广泛应用于农田灌溉、工矿企业的供排水和高原、山区的人、畜用水。
          进口井用潜水泵是由潜水泵和潜水电机组成一体潜入水下进行工作。具有结构简单、体积小、重量轻、安装、维修方便,运行安全、可靠、高效节能等特点。
          进口井用耐热潜水泵是与井用耐热圈三相异步电动机直接联成一体,组装成的耐热潜水电泵,耐热水温可达100℃, 是潜入井中,提取地热水的有效机具;地热是一种zui廉价,zui清洁,用之不竭的zui新能源,现今广泛应用于采暖、医疗、洗浴、养殖、种植、工农业、工矿企业、娱乐服务、保健设施等许多方面。它具有泵机合一,结构简单,运行可靠,无噪音,性能优良,机组效率高,安装维修方便;并具有耐热。防腐,抗老化等诸多特点,是提取地热水的zui新产品。

英国GRIMM格林进口井用潜水泵结构说明: 

1、进口井用潜水泵为离心式或混流式;采用水润滑轴承;与电机的联接采用联轴器刚性联接。泵叶轮在电机带动下旋转产生离心力,使液体能量增加经泵壳的导流作用进行提水。在水泵上端设有逆止阀体,防止电泵停机时,因扬水管中倒流的水损坏工作部件。阀上有泄水孔,可将管路中的水缓缓放掉,防止冬天冻裂管路。(注:低扬程潜水泵不设逆止阀体)
2、电机为密闭充水湿式结构。电机定子绕组采用耐水(耐热)的聚乙烯绝缘,尼龙护套多层结构的(耐热)电磁线。导轴承及推力轴承均采用水润滑材质。电机内部充满清水,用以冷却电机和润滑轴承。电机底部装有调压膜,用以调整由电机温升引起的机体内清水的胀缩压差。电机的上端轴上装有防砂机构,用来阻止水中泥砂进入机体内部。
3、管路部分:用以联接电泵使其吊装在机井中,将水输送到地面上去。主要由短输水管、输水管、弯管、夹板等部件组成。短输出管是输水管路与电泵的
连接过渡部件。弯管安装在井口处,以改变水流的传送方向。夹板是在电泵的安装过程中吊装和固定输出管路。

英国GRIMM格林进口井用潜水泵使用条件: 

1、电源要求:
(1)额定频率为50赫兹,电机端额定电压应保证为380±5%伏的三相交流电源(若用户电压为660伏时需特殊定货)。
(2)变压器负载功率不应超过其容量的75%。
(3)变压器距井较远时,应考虑输电线线压降,对功率大于45KW的电机,要求变压器到井口距离不超过20米。对于高扬程潜水电泵,由于输电线较长,必须考虑压降损耗,要求输电线规格比配电缆规格大两个等级。采用单台变压器供电,要求变压器输出电压400V-440V。
2、水质要求:
(1)一般无腐蚀性清水。
(2)水中含沙量不大于0.01%(质量比)。
(3)酸碱度PH值在6.5-8.5范围内。
(4)水中氯离子含量不大于400毫克/升。
(5)硫化氢含量不大于1.5毫克/升。
(6)井用潜水泵对水温不高于20℃。耐热潜水电泵对水温要求不高于100℃。
(7)不含有油类。
3、井筒要求:
      正直、光滑、不得有凸起或井管错位现象,井内径不小于相应的机座号。

英国GRIMM格林进口井用潜水泵技术参数:

流       量:8-400m3/h
扬       程:10-600m
功       率:0.37-220kw
额定电流:2.5-443.2A
额定电压:380±5%V,660V(需特殊定货)
额定频率:50HZ
机  座 号:100-350mm
机组径向:96-330mm

出水管直径:40-200mm

英国GRIMM格林进口井用潜水泵用途:

          进口井用潜水泵广泛应用于农田灌溉、工矿企业的供排水和高原、山区的人、畜用水。进口井用耐热潜水泵广泛应用于采暖、医疗、洗浴、养殖、种植、工农业、工矿企业、娱乐服务、保健设施等许多方面。

UK GRIMM Submersible pumps for imported wells summary:

         The import of submersible electric pump is an energy-saving product design according to the international standard, widely used in agricultural irrigation, industrial and mining enterprises for drainage and plateau and mountainous areas, drinking water.

         The pump is composed of submersible pump and submersible motor. It works underwater. The utility model has the advantages of simple structure, small size, light weight, convenient installation and maintenance, safe operation, reliability, high efficiency, energy saving, etc..

         Well with submersible pump heat is directly connected with the well heat circle of three-phase asynchronous motor, the assembled heat submersible pump, hot water temperature can reach 100 DEG C, is an effective tool to sneak into the wells, extraction of geothermal water; geothermal energy is one of the cheapest, most clean, inexhaustible new energy, is widely used in many aspects of heating, bathing, medical, breeding, cultivation, agriculture, industrial and mining enterprises, entertainment services, health care facilities etc.. The utility model has the advantages of simple pump structure, reliable operation, no noise, good performance, high unit efficiency, convenient installation and maintenance, and heat resistance. Anti corrosion, anti-aging and many other characteristics, it is the latest product of geothermal water extraction.

UK GRIMM Submersible pumps for imported wells structure description:

1.The submersible pump for the well is centrifugal or mixed flow. The water lubricated bearing is adopted. The coupling of the motor and the motor is connected by a rigid coupling. The pump impeller is driven by the motor to rotate to generate centrifugal force, so that the liquid energy is increased, and the water pumping is carried out by the diversion action of the pump shell. A non-return valve body is arranged at the upper end of the water pump to prevent the working parts of the water pump from being damaged by the backflow of water in the water pipe when the electric pump is stopped. The valve is provided with a drain hole of the water in the pipeline can be slowly discharged, to prevent the winter frost crack pipe. (Note: the low lift submersible pump does not have a non-return valve body)

2.The motor is closed water filled wet structure. The motor stator winding adopts water (heat resistant) polyethylene insulated, nylon sheath multilayer structure (heat resistant) electromagnetic wire. Guide bearings and thrust bearings are made of water lubricated material. The motor is filled with clean water to cool the motor and lubricate the bearings. The motor is arranged at the bottom of the pressure adjusting membrane, to adjust the motor temperature rise caused by the expansion and contraction of the water pressure difference. The upper end of the motor is provided with a sand prevention mechanism to prevent mud and sand from entering the interior of the machine.

3.Pipeline part: used to connect the electric pump, lifting it in the well, and transport the water to the ground. Mainly by short water pipe, water pipe, elbow, plywood and other components. The short output pipe is a connecting transition component between the water delivery pipe and the electric pump. The pipe is installed at the wellhead to change the direction of the flow. The clamping plate is lifting and fixing the output pipeline during the installation of the electric pump.

UK GRIMM Submersible pumps for imported wells conditions of use:

1.Power requirements:

(1) rated frequency is 50 Hz, the motor end rated voltage should be guaranteed to be 380 + 5% volts three-phase AC power supply (if the user voltage is 660 volts, special orders).

(2) the transformer load power should not exceed 75% of its capacity.

(3) when the transformer is far from the well, the voltage loss of the transmission line should be considered. The motor with power greater than 45KW requires that the distance from the transformer to the wellhead is not more than 20 meters. For high lift submersible pump, the transmission line is longer, must consider the pressure drop loss, transmission line cable specification requirements specifications than the two grade. The transformer output voltage is 400V-440V by using single transformer supply.

2.Water quality requirements:

(1) General non corrosive clean water.

(2) The sediment concentration in water is not more than 0.01% (mass ratio).

(3) PH value is within the range of 6.5-8.5.

(4) The content of chloride ion in water is not more than 400 mg / liter.

(5) Hydrogen sulfide content is not more than 1.5 mg / liter.

(6) The submersible pump for the well is not over 20 centigrade. Heat resistant submersible pump for water temperature is not higher than 100 degrees.

(7) Contains no oil.

3.Wellbore requirements:

   Upright, smooth, must not have the bulge or the well pipe dislocation phenomenon, the well bore diameter is not less than the corresponding frame number.

UK GRIMM Submersible pumps for imported wells technical parameter:

Flow rate: 8-400m3/h

Lift: 10-600m

Power: 0.37-220kw

Rated current: 2.5-443.2A

Rated voltage: 380 + 5%V, 660V (special order)

Rated frequency: 50HZ

Base number: 100-350mm

Unit radial: 96-330mm

Outlet pipe diameter: 40-200mm

UK GRIMM Submersible pumps for imported wells purpose:

         The import of submersible pump is widely used in agricultural irrigation, industrial and mining enterprises for drainage and plateau and mountainous areas, drinking water. Imported hot water submersible pumps are widely used in heating, medical treatment, bathing, breeding, planting, industry and agriculture, industrial and mining enterprises, entertainment services, health care facilities and many other aspects.

14979604996389173.png

进口井用潜水泵☞官网:http://www.021fmc.cn/aspcms/product/2018-5-11/1362.html 

14979604996389173.png

GRIMM中国:

    上海秉奇阀门有限公司GRIMM公司在中国的总代理,是中国拥有GRIMM代理权及销售权,主要为中国地区客户提供服务与技术支持,同时,秉奇人员也积极参与总部技术培训学习,并不断掌握产品原理、实际运作、工程技术做为基石,完善对中国地区客户需求。             

关于GRIMM

         英国格林(GRIMM)国际有限公司是亚太地区流体控制领域的主要生产和供应商之一,公司总部位于克莱福德,拥有一支有经验的研发队伍,实行全球统一设计,统一标准,在水泵领域内处于lingxian地位。在许多个国家均有生产水泵基地,中国由上海秉奇阀门负责中国市场各项业务与技术支持中心,同时向中国市场销售。

       英国格林(GRIMM)产品已广泛应用于市政给排水、建筑、石油、化工、液化气、食品、制药、发电、冶金、矿产、锅炉蒸汽系统、压力容器、原子能、航空、火箭等各领域,以及人们日常生活中。

       英国格林(GRIMM)主要产品有:管道泵、离心泵、隔膜泵、磁力泵、真空泵、潜水泵、排污泵、计量泵、卫生级泵、罗茨风机等系列产品。

服务体系:

GRIMM品质:

       GRIMM公司注重产品质量及使用寿命,全部采用先进制造技术和生产设备,并坚持不懈研发新产品,为确保不间断的全过程质量控制,在生产过程中采用(SPC)过程控制和(TQM)全面质量管理;GRIMM的严格规范实现了不让品质拖节,有效保障产品每个细节达到的性能指标。

GRIMM专业:

       掌握核心的流体控制技术,提供市场lingxian的产品、服务和解决方案,帮助用户提高效率,带来至关重要的基础设施。

GRIMM服务:

       我们与用户紧密合作,支持一系列系统使用技术和文件报告,提供售前、售中、售后服务和技术支持,有了您的信任与支持,我们将更完善、更高效提供水泵流体技术方案。

GRIMM china:

         Shanghai Bingqi Valve Co., Ltd. for GRIMM company general agent in China, is China with GRIMM proxy and sales rights, provide service and technical support, mainly for Chinese customers at the same time, will also actively participate in the training of technical personnel of butterfly learning headquarters, and continue to grasp the product principle, practical operation and Engineering Technology based on customer demand, improve the Chinese area.

About GRIMM:

         Uk GRIMM International Co., Lid is the field of fluid control in the Asia Pacific region is one of the main production and suppliers, the company headquarters is located in Clay Forde, has an experienced R & D team, the implementation of a global unified design, unified standards, a leading position in the field of water pump. In many countries, there are production pump base, China by the Shanghai Bingqi valve, responsible for the Chinese market business and technical support center, while selling to the Chinese market.

       Uk GRIMM products have been widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, metallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life.

       Uk GRIMM the main products are: pipeline pump, centrifugal pump, diaphragm pump, magnetic pump, vacuum pump, submersible pumps, sewage pumps, metering pumps, sanitary pump, blower and other products.

Service system:

GRIMM quality:

         GRIMM company pays attention to product quality and service life, all adopt the advanced manufacturing technology and production equipment, and unremittingly research and development of new products, the whole process of quality control to ensure uninterrupted, used in the production process (SPC) process control (TQM) and total quality management; strictly regulate the implementation of GRIMM has not let the quality drag day, effectively guarantee the performance of each product details.

GRIMM major:

          Fluid control technology master core, market leading products, services and solutions that help users improve efficiency, bring critical infrastructure.

GRIMM service:

          We work closely with the user, support a series of system using technology and file reports provide pre-sale, sale, customer service and technical support services, with your trust and support, we will be more perfect and more efficient to provide technical solutions of fluid pump.

14979604996389173.png

英国格林总代理商:上海秉奇阀门有限公司,微信咨询:

Uk GRIMM total agents: Shanghai Bingqi Valve Co., Ltd., WeChat Advisory:

 

Welcome new and old customers call negotiate!

Contacts:Huang Tianxiang

QQ:673088832

Mobile Phone:13524269805 (微信同号)

Company Phone:021-51698378

Add:Lane 51, dragon road, Shanghai, Xuhui District

报价承诺 价格说明 付款方式 保质期 关于运费 发票说明 投诉建议 交货期

进口阀门,进口水泵,进口电动球阀,进口气动角座阀,进口电动调节阀,进口拉断阀,进口水环式真空泵,进口电动隔膜泵-上海秉奇阀门有限公司 版权所有 沪ICP备15017877号-1
手 机:13524269805 电 话:021-51698378 传 真:021-69519069
邮 箱: 250996786@qq.com 网 址:http://www.021fmc.cn
地 址:上海市徐汇区龙漕路51号